UNIVERSAL TIRE ARBOR
Introducing a newly designed Tire Truer Arbor for truing foam tires mounted on Custom Works, BSR, RC4Less and any other wheels using a 3/16" axle and cross pin for the rear and 3/8" bearings on the front. This new design allows.... and fits all standard truers like Hudy...... etc.

#6240    UNIVERSAL TIRE ARBOR SET     Retail $49.00

NEW MOLDED FRONT ORANGE INSERT
Custom Works now has a molded front Orange Insert to match the #6236 Rear Insert used with our Sticker and Street Trac rubber tires. These now come standard in the premounted front tires and are available in pairs un-mounted as well.

#6232    MOLDED FRONT INSERT ORG     Retail $7.50

"STICKER 2" REAR RUBBER TIRE NOW AVAILABLE PRE-MOUNTED AND UN-MOUNTED
The newly redesigned Sticker 2 rear rubber tire is now available mounted or unmounted in both High Bite (HB) and Standard Compounds. Used in conjunctin with the Sticker Front tire these tires are intended for use on high bite cars like the Enforcer and Intimidator on smooth surfaces like clay and carpet. Pre-mounted tires come on the standard Custom Works 2.0" rubber tire wheels. Both front and rear tires are now available un-monted as well and we now have a new Orange/Medium Front Insert for use with these tires also.

All of these new items are available now from your favorite Custom Works Dealer or if you can't find them there you can order direct as well.

#6446 STICKER 2 Rear Pre Mount (Std/Org) Retail   $30.00
#6456 STICKER 2 Rear Pre Mount (HB/Org) Retail   $30.00
#6217 STICKER 2 Rear Tire Std Compound   Retail   $12.00
#6218 STICKER 2 Rear Tire HB Compound   Retail   $12.00

"BEEFED-UP" ADJUSTABLE TOE SUSPENSION ARMS FOR LOSI SCT AND ASSOCIATED SC10
To answer the "Where's the Beef" question from hard banging short course racers we added 50% more material around the inner hinge pin and adjusted the suspension arm material for more durability to account for the needs of racers running hard up in the high line by the wall.

#3272 Adjustable Arm Kit Associated SC-10 Retail   $45.00

#3274 Adjustable Arm Kit for TLR 22SCT Retail       $45.00

UPDATED FRONT SUSPENSION ARMS FOR ENFORCERS AND INTIMIDATORS
Now available for purchase and provided in all Intimidator and Enforcer kits raced with foam tires are these much stiffer and just as durable as the front suspension arms we have offered until now. Some ask if these are better than a machined suspension arms and the answer is a multi-sided YES! These arms are molded with a blend of nylon, carbon and fiberglass materials to provide a suspension arm that is durable, strong, rigid, ligtweight, dimensionally tolerant and lest costly for the racer vs that of a machined arm from materials like Delrin. 

#3251    NEW SHORT FRONT A-ARM       Retail $11.00

Ti-Nitride COATED SHOCK SHAFTS
Now available for purchase and provided in every CW kit are Ti-Nitride coated shocks shafts for our MDX2 Shocks. The Ti-Nitride coating not only helps make shock operation smoother but also increases shock life. The shock shafts are less prone to get worn by dirt and debris with the hard coating. The longer wearing surface of the shafts save with wear on the o-rings. Lastly the coating reacts with less "polishing effect" by the o-rings that turns the shock oil dark with use.

#1428    Ti-Nitride MDX Large Shock Shaft       Retail $3.50

#1429    Ti-Nitride MDX Medium Shock Shaft   Retail $3.50
#1430    Ti-Nitride MDX Short Shock Shaft       Retail $3.50

CAGED THRUST BEARING & THRUST WASHERS
In an effort to always improve we have replaced the standard thrust washers with these thrust bearing races that fit the caged thrust bearing assembly perfectly. The grooved surface or "race" assembles facing the thrust bearing and allows for the smoothest operation possible.

#4367    CAGED THRUST BEARING              Retail $4.00

TRUESPEED 48 PITCH PINION GEARS
Building off customer demand from our well received line of spur gears are 48 pitch hard coated aluminum pinions gears in sizes 15 thru 30 teeth. Light weight and true to pitch these gears will help you find the right gearing for speed and control at your local track all with quiet operation.

#TS4815-30 TRUESPEED 48P SPUR GEARS Retail $6.50

BIG BORE spring assortment for TRAXXAS and other Short Course Trucks
Racers looking to tune their Short Course trucks for dirt oval racing have to look no further than this spring assortment. Proudly made in the USA means these springs are consistent in rate from one spring to the next but also the spring will not fatigue and become considerably shorter with use like some other springs offered of lesser quality. This spring kit offers rates of 5, 6, 7, and 8 pounds which should account for all your needs on typical dirt oval tracks. These springs along with our adjustable toe suspension arms and Tornado body make for a huge improvement of handling and speed for your short course to dirt oval racer!

#1820 BIG BORE Shock Spring Set for SC Retail $22.00

#1825 Yellow BIG BORE Shock Spring 5LB Retail $6.00
#1826 Red BIG BORE Shock Spring 6 LB Retail $6.00
#1827 Green BIG BORE Shock Spring 7 LB Retail $6.00
#1828 Purple BIG BORE Shock Spring 8 LB Retail $6.00

R2 FOAM TIRE COMPOUNDS
Derived from the popular "X" series of foam rubber compounds, the "R" series foam rubber has a better wear characteristic than the same density X2 but with slightly less grip at most tracks. The are a good choice for right side tires when X2's are wearing a little more than you would like. Also using them as a full set works very well when the track is tacky or wet and you need the car to roll easier and not be "stuck in the mud". Just like our other popular foam racing tires, the "letter" indicates the rubber type and is followed by a number that tells you the density rating of the foam compound...so the higher the number the greater the density.

#6247 FRONT MOUNTED R2 COMPOUND Retail $26.00

#6297 REAR MOUNTED R2 COMPOUND Retail $29.00

CAGED THRUST BEARING ASSEMBLY
Gone are the days of trying to wrangle down the 6 tiny balls for the diff screw. This item is now a stock part in all kits, and fits CustomWorks differentials for electric, nitro and new style direct drive transmissions.

#4367    CAGED THRUST BEARING              Retail $3.00

TITANIUM FRONT AXLES
This option part is a direct replacement for the front axles in all CustomWorks kits not using the inclined spindles. Made in the USA from titanium this is the best axle you can have on your hot rod for weight and durabilty. Why even think about a steel axle if you happen to bend the stock aluminum axle??? This is the last front axle you will ever buy if you race the high side hard and fast!..

#7222 TITANIUM FRONT AXLE Retail $13.00

MACHINED OUTDRIVE BLADES
This is the best blade we offer and lasts multiple races provided you put a tad bit of diff lube on it prior to the race day. The blade type design allows the rear suspension to move easier while under constant drive from the motor making the car turn easier thru the centers of the corner and off. Blade type outdrives are suggested for all dirt oval racing using foam tires, mod to stock. Also they are suggested for loose dirt rubber tire cars provided the power of the class is 13.5 blinky or less.

#4383 MACHINED OUTDRIVE BLADES Retail $5.00

TORNADO MOD BODY FOR SC TRUCKS
CustomWorks has released a "Tornado" for the dirt oval racer!Inspired by the real cars that race in the USMTS, IMCA, or UMP series across the nations heartland, the Tornado is a mid-western style dirt oval body sized for a variety of short course vehicles including Traxxas Slash, Associated, Losi as well as others. Molded from quality impact resistant polycarbonate the shape of the body panels provide both great looks and rigid form. The body kit includes all panels shown, pre-cut and formed spoiler, window masks, hardware, and basic accent decal set. CustomWorks is the dominate force in dirt oval racing offering competition quality racing kits and supplies since 1988

#9211 TORNADO MOD for SC TRUCKS Retail $59.00

STREET STOCK CAMARO
Custom Works is pleased to announce the release of our #9075 1/10 Street Stock CAMARO Body. Based off of our original 9002 ASA/IROC Camaro mold this new release features pre-cut window masks and also includes a decal sheet for some added details. This body is perfect for any street stock type of class and fits most 1/10th scale buggies as well as any 1/10th oval based latemodel style chassis.

#9075 STREET STOCK CAMARO BODY Retail $29.00

TRUESPEED 48 PITCH SPUR GEARS
Lightweight, True, and Quiet these are the best machined gears from sizes 85 thru 96 teeth. All gears have their size machined clearly into the part so there is no guessing which gear you have on the car.

#TS6885-96 TRUESPEED 48P SPUR GEARS Retail $8.00

 

Continue Shopping

Company

About Us

Support

customworkssales@aol.com
704-489-8147

Connect with us

Copyright © 2016 CustomworksRC